LSC050I29-MP-V1: 5.0-inch TFT LCD Module, 720×1280, MIPI Interface, 16.7M Colors, Transmissive IPS
Product Subtitle / Keywords
5.0 Inch Display, 720(RGB)×1280 Resolution, Transmissive a-Si TFT-LCD Module, COG+FPC+B/L+CTP Module Type, MIPI Interface, 16.7M Colors, IPS Display Mode, Module Size (H×V×D): Approx. 70.6 × 67.88 × 3.6 mm, Active Area (H×V): Approx. 61.48 × 109.20 mm, Operating Temp: -20°C ~ +70°C, Storage Temp: -30°C ~ +80°C, Backlight: White LED (If=40mA, Vf=16.8~17.4V), Driver IC: FL7703NI, RoHS Compliant, Product Version 1.0
1. Executive Summary And Product Positioning
The LSC050I29-MP-V1 is a 5.0-inch diagonal transmissive type a-Si TFT-LCD (amorphous silicon thin film transistor liquid crystal display) module, manufactured by Lesson (Wanan) Smart Display Technology Co., Ltd. This comprehensive module integrates a TFT-LCD panel, a driver circuit, a backlight unit (B/L), and a Capacitive Touch Panel (CTP) into a single package. The product specification (Revision 1.0) serves as the definitive technical document for this module.
This module features a resolution of 720(RGB)×1280 pixels (HD) and is capable of displaying up to 16.7M colors (8-bit). The module uses a MIPI interface and is driven by the FL7703NI driver IC. The module includes a CTP with an I2C interface (TP-SDA, TP-SCL).
2. Detailed Product Overview And Architecture
The LSC050I29-MP-V1 is a 5.0-inch TFT display with an integrated touch panel. Its architecture is built around several key elements:
- Core Technology: Transmissive type a-Si TFT-LCD. The display mode is IPS.
- Module Type: COG (Chip-On-Glass) + FPC (Flexible Printed Circuit) + B/L (Backlight) + CTP (Capacitive Touch Panel).
- Display Format: Graphic 720(RGB)×1280 Dot-matrix (HD).
- Display Characteristics: Capable of displaying up to 16.7M colors.
- Interface Type: MIPI interface for LCD. The touch panel uses an I2C interface (TP-SDA, TP-SCL).
- Main LCD Driver IC: The module integrates the FL7703NI driver IC.
- Backlight Unit: The module utilizes a white LED backlight. The driving condition is IF=40mA and VF=16.8~17.4V.
- View Direction: IPS (ALL).
- Approval Status: Approved Product Specification only (Revision 1.0).
3. Technical Specifications
3.1 General & Mechanical Specification
The module outline dimensions are provided in the drawing. Key mechanical parameters are as follows:
| Parameter | Specification | Unit |
|---|---|---|
| Panel Size | 5.0'' (Diagonal) | Inch |
| Module Outline (H×V×D) | Approx. 70.6 × 67.88 × 3.6 (from diagram) | mm |
| Active Area (H×V) | 61.48 × 109.20 (approximated from diagram) | mm |
| Number of Dots | 720(RGB) × 1280 | pixels |
| Display Type | a-Si TFT, Transmissive, IPS | - |
| Display Colors | 16.7M | colors |
| Module Type | COG+FPC+B/L+CTP | - |
| Display Mode | IPS | - |
| View Direction | IPS (ALL) | - |
| Driver IC | FL7703NI | - |
| Interface | MIPI (LCD) / I2C (CTP) | - |
| Touch Panel Type | Capacitive (CTP) | - |
| Backlight Type | White LED | - |
3.2 Absolute Maximum Ratings
The document does not contain an explicit \"Absolute Maximum Ratings\" table for the LSC050I29-MP-V1. The primary specifications are contained within the Electrical Characteristics section.
3.3 Electrical Characteristics
The electrical characteristics table from the specification is as follows:
| Item | Symbol | Min | Typ | Max | Unit | Remark |
|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.5 | 2.8 | 6.6 | V | Note1 |
| Supply voltage | IOVCC | 1.65 | 2.8 | 3.6 | V | Note1 |
| Input Voltage (L level) | VIL | 0 | --- | 0.3*IOVCC | V | Note1 |
| Input Voltage (H level) | VIH | 0.7*IOVCC | --- | IOVCC | V | Note1 |
3.4 Backlight Driving Conditions
The document specifies the backlight driving condition as: IF=40mA, VF=16.8~17.4V. The backlight circuit diagram shows 12 LEDs in a configuration (presumably 6 series 2 parallel).
| Parameter | Symbol | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|
| Backlight Forward Voltage | VF | 16.8 | - | 17.4 | V |
| Backlight Forward Current | IF | - | 40 | - | mA |
3.5 Interface Connection (FPC)
The module uses a 34-pin FPC. The pin description table from the specification is as follows:
| PIN NO. | Symbol | I/O | Description |
|---|---|---|---|
| 1 | GND | - | Ground |
| 2 | NC | - | Not connect |
| 3 | LCD-PWM | O | Backlight LED driver PWM |
| 4 | GND | - | Ground |
| 5 | LCD-TE | O | Tearing signal output from driver IC |
| 6 | LANE2-P | I | MIPI data2 positive signal |
| 7 | LCD-RESET-N | I | Device reset signal |
| 8 | LANE2-N | I | MIPI data2 negative signal |
| 9 | LCD-ID-0 | - | ID0 (GND) |
| 10 | GND | - | Ground |
| 11 | LCD-ID-1 | - | ID1 (NC) |
| 12 | LANE1-P | I | MIPI data1 positive signal |
| 13 | GND | - | Ground |
| 14 | LANE1-N | I | MIPI data1 negative signal |
| 15 | VSN | I | Power supply for analog (-5.0V) |
| 16 | GND | - | Ground |
| 17 | VSN | I | Power supply for analog (-5.0V) |
| 18 | CLK-P | I | MIPI clock positive signal |
| 19 | VSP | I | Power supply for analog (+5.0V) |
| 20 | CLK-N | I | MIPI clock negative signal |
| 21 | VSP | I | Power supply for analog (+5.0V) |
| 22 | GND | - | Ground |
| 23 | VDD-1V8 | I | Power supply for I/O (1.8V) |
| 24 | LANE0-P | I/O | MIPI data0 positive signal |
| 25 | GND | - | Ground |
| 26 | LANE0-N | I/O | MIPI data0 negative signal |
| 27 | LED-ANODE | - | LED back light power positive |
| 28 | GND | - | Ground |
| 29 | NC | - | Not connect |
| 30 | LANE3-P | I | MIPI data3 positive signal |
| 31 | LED-CATHODE1 | - | LED back light power group1 negative |
| 32 | LANE3-N | I | MIPI data3 negative signal |
Note: The pinout shows 4 MIPI data lanes (LANE0, LANE1, LANE2, LANE3) supporting up to 4-lane MIPI operation.
4. Application Scenario (Based on Spec)
Based on the product specification, this module is a 5.0-inch HD TFT display with an integrated capacitive touch panel, suitable for high-end portable devices, smart home control panels, and industrial handheld terminals that require a responsive touch interface.
5. Handling Precautions And Compliance
The module is compliant with the RoHS directive. The document also includes specific mechanical design guidelines: case visual area should be 0.3mm smaller than VAmds per side, foam opening should be 0.6mm larger than VAmds per side, and TP edge should not contact any metal conductor.
