LSC060I03-MP-V1 5.99 inch TFT-LCD Module 1080x2160 16.7M Colors IPS
1. Executive Summary & Product Positioning
The LSC060I03-MP-V1 is a 5.99-inch IPS type TFT LCD module developed by 立信(万安)智显科技有限公司 (Lesson Smart Display Technology Co., Ltd). The resolution is 1080(RGB)*2160, and it is a high-definition display module built with COG+FPC+B/L+LENS technology. It is suitable for handheld devices and meets standards such as ROHS.
Product Positioning: This module features a 5.99-inch IPS (In-Plane Switching) panel, offering a high resolution of 1080x2160. With a standard 4-lane MIPI interface, it is well-suited for a wide range of applications such as high-end handheld devices, industrial HMI, and other embedded display systems requiring a sharp and reliable display with a protective lens.
2. Detailed Product Overview & Architecture
The module's architecture is designed for robust performance and easy integration. The primary components include:
- TFT-LCD Panel: 5.99-inch diagonal, a-Si TFT active matrix, transmissive, IPS mode (6 O'CLOCK viewing direction). Resolution is 1080(RGB) × 2160 pixels.
- Driver Circuit: The module integrates an ILI77600A-X1 driver IC, communicating via a MIPI Interface.
- Backlight Unit (B/L): A white LED backlight with LEDs configured in a 4 Series 4 Parallel (4S4P) arrangement. The typical driving condition is IF=80mA, Vf=24V (TYP). The typical luminance is 600 cd/m².
- Mechanical Construction: COG (Chip-on-Glass) + FPC + B/L + LENS (Cover Glass). The module outer dimensions are approximately 68.0 (W) × 141.0 (H) × 2.0 (D) mm (based on typical 5.99" and 18:9 aspect ratio).
- Interface: The module communicates via a 40-pin FPC connector. The display interface is MIPI (4 Data Lane).
- Display Mode: Active matrix TFT, Transmissive type, IPS (6 O'CLOCK).
- Surface Hardness: ≥6H (for the lens).
- RoHS: All materials are compliant with ROHS standards.
3. Exhaustive Technical Specifications
3.1 General & Mechanical Specifications
| Item | Specification |
| Display Size (Diagonal) | 5.99 inches |
| Resolution (Dots) | 1080(RGB) × 2160 |
| Display Technology | Active Matrix TFT, Transmissive, a-Si, IPS (6 O'CLOCK) |
| Module Construction | COG+FPC+B/L+LENS |
| Color Depth | 16.7M Colors |
| Viewing Direction (Grayscale Inversion) | 6 O'CLOCK (IPS) |
| Input Data Interface | MIPI (4 Data Lanes) |
| Driver IC | ILI77600A-X1 |
| Display Type | IPS (6 O'CLOCK), Transmissive, Normally Black (TBD) |
| Backlight Type | White LED, 4S4P (4 series, 4 parallel) |
| Luminance (IF=80mA) | 600 cd/m² (Typ) |
| Lens Hardness | ≥6H (for light surface) |
| Lens Transmittance | ≥92% |
| Operating Temperature | -20°C to +70°C |
| Storage Temperature | -30°C to +80°C |
| Environmental Compliance | ROHS |
3.2 Electrical Characteristics
3.2.1 Backlight LED Characteristics
The backlight driving condition is IF=80mA, Vf=24V (TYP) for a 4S4P LED configuration.
| Parameter | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Forward Voltage | Vf | -- | 24.0 | -- | V |
| Forward Current (Total) | IF | -- | 80 | -- | mA |
3.3 Interface Pin Assignment (40-Pin FPC)
The module communicates via a 40-pin FPC connector. The interface is MIPI.
| PIN NO. | Symbol | I/O | Description |
|---|---|---|---|
| 1-2 | LEDA | P | Power for LED backlight anode |
| 3-4 | LEDK | P | Power for LED backlight cathode |
| 5 | GND | P | Power Ground |
| 6 | VDDIO(1.8V) | P | Power supply for logic (1.8V) |
| 7 | VDD(2.8V) | P | Power supply for TFT (2.8V) |
| 8 | GND | P | Power Ground |
| 9 | LCM_RST | I | LCD Reset pin |
| 10 | GND | P | Power Ground |
| 11 | DSI_0P | I | MIPI Data lane 0 positive-end input |
| 12 | DSI_0N | I | MIPI Data lane 0 negative-end input |
| 13 | GND | P | Power Ground |
| 14 | DSI_1P | I | MIPI Data lane 1 positive-end input |
| 15 | DSI_1N | I | MIPI Data lane 1 negative-end input |
| 16 | CLKP | I | MIPI Clock lane positive-end input |
| 17 | CLKN | I | MIPI Clock lane negative-end input |
| 18 | GND | P | Power Ground |
| 19 | DSI_2P | I | MIPI Data lane 2 positive-end input |
| 20 | DSI_2N | I | MIPI Data lane 2 negative-end input |
| 21 | GND | P | Power Ground |
| 22 | DSI_3P | I | MIPI Data lane 3 positive-end input |
| 23 | DSI_3N | I | MIPI Data lane 3 negative-end input |
| 24 | GND | P | Power Ground |
| 25 | GND | P | Power Ground |
| 26 | D0P | I | MIPI Data lane 0 positive-end input (labeled D0P in drawing) |
| 27 | D0N | I | MIPI Data lane 0 negative-end input (labeled D0N in drawing) |
| 28 | GND | P | Power Ground |
| 29 | D1P | I | MIPI Data lane 1 positive-end input (labeled D1P in drawing) |
| 30 | D1N | I | MIPI Data lane 1 negative-end input (labeled D1N in drawing) |
| 31 | GND | P | Power Ground |
| 32 | D2P | I | MIPI Data lane 2 positive-end input (labeled D2P in drawing) |
| 33 | D2N | I | MIPI Data lane 2 negative-end input (labeled D2N in drawing) |
| 34 | GND | P | Power Ground |
| 35 | D3P | I | MIPI Data lane 3 positive-end input (labeled D3P in drawing) |
| 36 | D3N | I | MIPI Data lane 3 negative-end input (labeled D3N in drawing) |
| 37 | PWM | I | PWM signal for backlight brightness control |
| 38 | TP_INT | I | TP Interrupt signal (if applicable) |
| 39 | TP_SCL | I | I2C clock for TP (if applicable) |
| 40 | TP_SDA | I | I2C data for TP (if applicable) |
Note: The pin assignment includes both MIPI signals and backlight (LEDA/LEDK) pins. The PWM pin (37) is dedicated for backlight brightness control. Pins 38-40 (TP related) may be NC (No Connection) or used for a separate touch controller depending on the specific variant.
3.4 Electrical Specifications
3.4.1 Power Supply Specifications
The module has a PWR Mode section with defined voltage ranges.
| Parameter | Symbol | Range | Unit |
|---|---|---|---|
| Analog Power Supply | AVDD | 4.5 - 6.5 | V |
| Analog Power Supply (Negative) | AVEE | -6.5 to -4.5 | V |
| IO Logic Supply | VDDI | 1.65 - 1.95 | V |
| Gate High Voltage | VGH | 6 - 16 | V |
| Gate Low Voltage | VGL | -12 to -5 | V |
3.5 Optical Characteristics
Condition: Ta=25°C, viewing angle at center point, θx=θy=0.
| Item | Symbol | Condition | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|---|
| Luminance | Lv | IF=80mA | -- | 600 | -- | cd/m² |
3.6 ESD Characteristics
ESD (Electrostatic Discharge) test conditions for the module with backlight.
| Test Item | Test Condition | Remark | Class |
|---|---|---|---|
| ESD | 150pF, 330Ω, Contact: ±4KV, Air: ±8KV | 1 | Class B |
| ESD | 200pF, 0Ω, ±200V contact test | 2 | Class B |
3.7 Soldering Conditions
The soldering conditions are specified for the module's I/O terminals.
- Temperature: 280°C ± 10°C
- Time: 3 to 4 seconds
- Method: Use eutectic solder with resin flux fill. If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed afterwards.
- Desoldering: Use proper suction type desoldering irons. Do not repeat the soldering/desoldering process more than three times.
3.8 Design Notes from Documentation
- B/L Driver: The backlight driving condition is IF=80mA, Vf=24V (TYP) for a 4S4P LED configuration. An external boost converter is required.
- Mechanical: Unspecified tolerances are ±0.2mm (unless otherwise stated). The module includes a protective lens with hardness ≥6H.
- Housing: It is recommended that the housing visual area be at least 0.3mm smaller than the VA (Viewing Area) on each side. The housing foam window should be at least 0.6mm larger than the VA on each side.
- Storage Environment: -30°C ~ +80°C, ≤90% RH.
- Working Environment: -20°C ~ +70°C, ≤90% RH.
- Interface: The display uses a 4-lane MIPI DSI interface. The power supply sequence must be carefully controlled.
- RoHS: All materials must be compliant with ROHS standards.
4. Application Guidelines & Critical Notes
- Power Supply: The module requires a 2.8V (VDD) and 1.8V (VDDIO) power supply as per pin definition. Ensure the power supply ripple is minimized.
- Interface: This module uses a standard MIPI DSI (4-lane) protocol. The host processor must be configured for this protocol.
- Backlight Driver (External): An external constant current driver is required to supply the backlight via the LEDA and LEDK pins. The required driving condition is 80mA total current at 24V forward voltage (Typ). PWM dimming control can be implemented using the dedicated PWM pin (Pin 37).
- Reset: A hardware reset pin (LCM_RST, Pin 9) is provided. It must be applied properly to initialize the LSI.
- ESD Protection: The module has specified ESD performance (Class B). Ensure proper grounding and handling procedures during assembly.
- Handling Precautions: Handle the module with care to avoid damage to the glass or FPC. Ground yourself to prevent electrostatic discharge (ESD).
5. Conclusion & Design-In Support
The LSC060I03-MP-V1 from Lesson Smart Display Technology is a 5.99-inch IPS TFT-LCD module with a 4-lane MIPI interface. It is a high-resolution, wide-viewing-angle display solution suitable for a wide variety of industrial and consumer embedded display applications.
For successful design-in, engineers should:
- Obtain and review the complete, official Product Specification (Revision 1.0) for the full mechanical drawing and the driver IC (ILI77600A-X1) datasheet for detailed initialization and timing parameters.
- Design a clean 2.8V/1.8V power supply for the LCD. Design a backlight boost converter and constant current driver circuit capable of delivering 80mA at 24V.
- Configure the host processor's MIPI DSI (4-lane) interface to match the timing specifications detailed in the datasheets.
- Contact the manufacturer for evaluation modules, sample requests, and further technical support during the design-in phase.
This module is designed to provide a reliable and vibrant display solution for a wide array of applications.
